pepperl-fuchs logo (www.hermestrading.ir)

HID2082

2-channel isolated barrier

24 V DC supply (bus powered)

Thermocouple, RTD or potentiometer input

Usable as signal splitter (1 input and 2 outputs)

Linearized output 4 mA … 20 mA, sink/source or 1 V … 5 V

Sensor breakage detection

Configurable by PACTware

Line fault detection (LFD)

Up to SIL 2 acc. to IEC 61508/IEC 61511

در صورت داشتن هرگونه سوال از محصول و خرید با ما در تماس باشید

توضیحات

HID2082 Pepperl+fuchs

  • 2-channel isolated barrier
  • 24 V DC supply (bus powered)
  • Thermocouple, RTD or potentiometer input
  • Usable as signal splitter (1 input and 2 outputs)
  • Linearized output 4 mA … 20 mA, sink/source or 1 V … 5 V
  • Sensor breakage detection
  • Configurable by PACTware
  • Line fault detection (LFD)
  • Up to SIL 2 acc. to IEC 61508/IEC 61511

HID2082 Pepperl+fuchs

General specifications
Signal type Analog input
Supply
Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage 20.4 … 30 V DC bus powered via Termination Board
Ripple within the supply tolerance
Current ≤ 95 mA at 20.4 V and ≤ 63 mA at 30 V
Power consumption ≤ 1.95 W
Interface
Programming interface programming socket
Input
Connection side field side
Connection SL2: 5a(+), 1a(+), 1b(-), 5b(-); 7a(+), 3a(+), 3b(-), 7b(-)
RTD type Cu10, Cu50, Cu100, Pt10, Pt50, Pt100, Pt500, Pt1000, Ni100 (EN 60751: 1995)
type Pt10GOST, Pt50GOST, Pt100GOST, Pt50GOST, Pt1000GOST (P50353-92)
Measuring current approx. 200 µA with RTD
Types of measuring 2-, 3-, 4-wire connection
Lead resistance max. 50 Ω per line
Measurement loop monitoring sensor breakage, sensor short-circuit
Thermocouples type B, E, J, K, N, R, S, T (IEC 584-1: 1995)
type L (DIN 43710: 1985)
type TXK, TXKH, TXA (P8.585-2001)
Cold junction compensation at field terminals
Measurement loop monitoring sensor breakage
Potentiometer 0.1 … 20 kΩ
Types of measuring 3-wire connection
Voltage selectable within the range -100 … 100 mV
Input resistance min. 1 MΩ (-100 … 100 mV)
Output
Connection side control side
Connection SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Output I, II analog, current or voltage output
Current range 0/4 … 20 mA
Voltage range 0 … 5 V or 1 … 5 V (on 250 Ω, 0.1 % internal shunt)
Fault signal downscale 0 or 2 mA, upscale 21.5 mA (acc. NAMUR NE43)
Source load 0 … 550 Ω , open-circuit voltage ≤ 18 V
Sink Voltage across terminals 7 … 30 V. If the current is supplied from a source > 20 V,
series resistance of ≥ (V – 20)/0.0215 Ω is needed, where V is the source voltage.
The maximum value of the resistance is (V – 7)/0.0215 Ω.
Fault indication output
Connection SL1: 6b
Output type open collector transistor (internal fault bus)
Transfer characteristics
Deviation
After calibration Pt100: ± (0.05 % of measurement value in °C + 0.05 % of span + 0.1 K (4-wire connection))
thermocouple: ± (0.05 % of measurement value in °C + 0.05 % of span + 1 K (1.2 K for types R and S))
This includes ± 0.8 K error of the cold junction compensation
Influence of ambient temperature current output (deviation of CJC included):
Pt100: ± (0.0015 % of measurement value in K + 0.006 % of span)/K ΔTamb*)
thermocouple: ± (0.02 K + 0.01 % of measurement value in K + 0.006 % of span)/K ΔTamb*)

*) ΔTamb = ambient temperature change referenced to 23 °C (296 K)

Influence of supply voltage < 0.01 % of span
Influence of load ≤ 0.1% of full scale from 0 … 550 Ω
Reaction time worst case value (sensor breakage and/or sensor short circuit detection enabled)
mV: 1.2 s, thermocouples with CJC: 1.4 s, thermocouples with fixed ref. temp: 1.4 s, 3- or 4-wire RTD: 1.1 s, 2-wire RTD: 920 ms
Galvanic isolation
Power supply/programming input There is no electrical isolation between the programming input and the supply.
The programming cable provides galvanic isolation so that ground loops are avoided.
Indicators/settings
Display elements LEDs
Control elements DIP-switch
Configuration via DIP switches
via PACTware
Labeling space for labeling at the front
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility NE 21:2006
For further information see system description.
Degree of protection IEC 60529:2001
Ambient conditions
Ambient temperature -20 … 60 °C (-4 … 140 °F)
Relative humidity 5 … 90 %, non-condensing up to 35 °C (95 °F)
Mechanical specifications
Degree of protection IP20
Mass approx. 140 g
Dimensions 18 x 106 x 128 mm (0.7 x 4.2 x 5 inch)
Mounting on Termination Board
Coding pin 2 and 4 trimmed
For further information see system description.
Data for application in connection with hazardous areas
EU-type examination certificate CESI 02 ATEX 086
Marking Ex-Hexagon II (1)G [Ex ia Ga] IIC
Ex-Hexagon II (1)D [Ex ia Da] IIIC , (-20 °C ≤ Tamb ≤ 60 °C)
Input [Ex ia Ga] IIC, [Ex ia Da] IIIC
Voltage 10 V
Current 15 mA
Power 38 mW
Analog outputs, power supply, collective error
Maximum safe voltage 250 V (Attention! This is not the rated voltage.)
Interface
Maximum safe voltage 250 V (Attention! The rated voltage is lower.), RS 232
Certificate PF 11 CERT 2109 X
Marking Ex-Hexagon II 3G Ex nA nC IIC T4
Galvanic isolation
Input/input 125 V AC max. common voltage between isolated channels (mV or thermocouple inputs only)
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/Programming input safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity
Directive 2014/34/EU EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010
International approvals
CSA approval
Control drawing 366-017CS-12 (cCSAus)
IECEx approval IECEx TUN 04.0012
Approved for [Ex ia] IIC
General information
Supplementary information Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Accessories
Designation optional accessories:
– resistance thermometer for cold junction compensation H-CJC-SP-8
– adapter with USB Interface K-ADP-USB

Classifications

System Classcode
ECLASS 11.0 27210129
ECLASS 10.0.1 27210129
ECLASS 9.0 27210129
ECLASS 8.0 27210190
ECLASS 5.1 27210107
ETIM 8.0 EC002919
ETIM 7.0 EC002919
ETIM 6.0 EC002919
ETIM 5.0 EC001485
UNSPSC 12.1 32101514

HID2082 Pepperl+fuchs

This isolated barrier is used for intrinsic safety applications.

This device accepts thermocouples (TC), millivolts, potentiometers, or resistance temperature detectors (RTD) from a hazardous area and converts them to an isolated, linearized analog output in the safe area.

The outputs can be selected as a current source, current sink, or voltage source with DIP switches on the side panel.

The device can also be configured as a signal splitter.

Line fault detection of the field circuit is indicated by a red LED and an output on the fault bus. The fault conditions are monitored via a Fault Indication Board.

The device is easily configured by the use of the PACTware configuration software.

This device mounts on a HiD Termination Board.

HID2082 Pepperl+fuchs

If you need a specific HID2082 Pepperl+fuchs firmware or series, then we probably have it. Please call or email us your request.

call: +982188856017
Email: info@hermestrading.ir

شركت هرمس نیلگون مایا با هدف ارتقاء سطح كيفي تجهيزات فني و آزمايشگاهی، نفت، گاز، پتروشیمی، دانشگاهی، عمرانی و همچنين تامین تجهیزات  روز دنيا به كشور ايران وارد اين عرصه گرديده.
اين شركت با اعتماد قابل تقدير شما عزيزان توانسته است در مدت زماني كوتاه با كسب موفقيت های چشمگير، نامی قابل اعتماد در زمينه تامین تجهيزات نوين و پيشرفته فنی و آزمايشگاهی در سراسر كشور داشته باشد.
ما با حضوری فعال و کم نظیر سعی نموده ایم تا با مشاوره فنی، معادل و بهینه سازی تجهیزات مورد نیاز، انبار موجودی و امکان تحویل فوری، دفاتر برون مرزی در اروپا و آسیا و عاملیت فروش برند های معتبر و فعال در صنعت کشور، موجبات تامین آسوده، کم هزینه و ایمن را برای کاربران خود فراهم آوریم و گامي مهم در زمينه تامین کالا  و ارائه تجهيزات پيشرفته در صنعت نفت، گاز، پتروشیمی برداریم. با ما در تماس باشید.

HID2082 Pepperl+fuchs

نقد و بررسی‌ها

هیچ دیدگاهی برای این محصول نوشته نشده است.

اولین کسی باشید که دیدگاهی می نویسد “HID2082”

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *